60' 0" 1994 BERTRAM Motor Yacht

Fort Lauderdale Florida U.S.
$795,000 USD
Fuel Capacity:
1630 gal
1994 / 2016 (Refit)
Fuel Type:
Engine Model:
2 x 16V 2000
Engine Manufacturer:
60' 0"
16' 11"
Hull Material:
“MELINA” began as a production Bertram 60 Convertible.  This vessel has been highly customized at significant expense to the owner whom has upgraded all navigation electronics, reconfigured and upgraded the interior, repowered with new engines, marine gears and new generators.  The vessel has very low hours on the main engines and generators since 2008.  New shafts, struts, propellers, shaft logs, rudders and rudder ports have been renewed in the past several years as well.  

The interior was reconfigured and significantly upgraded in 2007.  The most notable upgrade was the destruction of the galley down arrangement and converting the space into a custom Tackle Room.  The galley is now in the forward salon area and has solid surfacing counter tops, refinished cabinets, wet bar and new appliances.

The tackle room is a one of a kind custom space that securely stores the extensive collection of professional Bill and Tuna fishing equipment.  The reflection from the phenolic mirror material gives the appearance of a much larger area.  

The head spaces were renovated and upgraded with new marine grade toilets, solid surfacing, wall coverings and overhead coverings during 2007.  The soles are Teak and Holly.  A new Black water holding system and all hoses were also renewed. The quality of the refit is done to a professional standard.  All finish and joiner work are of the highest quality.  The current configuration and finish is that found in one of a kind, high quality custom yacht.

The vessels exterior was professional prepared and painted in 2015 at American Custom Yachts.  The vessels superstructure is white with blue feature stripes that match the hull coating of dark blue.  The hull was previously light blue.  The transom and raised fiberglass toe rail have been coated using an Air Teak or similar coating system and significantly add to the visual appeal of the vessel.  The visual appearance and quality of the exterior finish is that you would expect on very high end yachts.

The vessel was repowered in 2008 by Jarrett Bay Boat Works Inc. which consisted of removing the original V16-92DDC 1450 hp engines and installing new M91 2000 MTU/DDC 1,800 hp engines, controls and new marine gears.  The running gear was upgraded to accommodate new 3.5” Aqua Met 22HS shafting that was required to accommodate the 1,800 horse power engines with ZF 2070A 2.25:1 marine gears.  Mr. Lee Dana Engineered the running gear requirements.  New Veem Interceptor propellers were sized, purchased and installed to efficiently utilize the upgrade in horse power.  New Onan EQD generators were installed.  New LIVOS ventilation system was installed.  New DC wiring, batteries, switching etc. were renewed as well.  It would cost approximately $900,000 to $1,000,000.00 to perform similar work at today’s costs.

The combined mechanical, interior refit, exterior painting, and tower hard top has converted this vessel into a highly customized Bertram 60 convertible into a one of a kind custom sport fishing vessel capable of a top speed of 41.5 kts.  
MELINA is a raised foredeck, stepped sheer, salon house with fly bridge superstructure sport fishing motor yacht constructed by Bertram Yacht of Miami Florida.
  • Custom aluminum pipe weld constructed full tower with upper station above the flybridge fitted with a custom fiberglass fabricated sole in 2008
  • Custom fiberglass hard top over the fly bridge fitted with recessed LED lighting and custom SST teaser reels new in 2007
  • The fly bridge is enclosed with an EZ2CY custom five panel enclosure new in 2007
  • There are new high quality marine vinyl bolsters white in color with blue beading installed 2015
  • The fly bridge helm is fitted with modern navigational equipment designed for optimal offshore sport Bill and Tuna fishing
  • The helm console was custom built in 2008 and a custom display panel with engine function monitors, switching and indicator lights for high water, bilge pumps and navigation light controls installed
  • A set of Rupp Hydraulic 18904 big gun out riggers were installed by Bausch American Inc. in 2012
  • The helm area has two Release Marine Teak helm chairs equipped with foot pedestals, slides and rotational bases installed in 2014
  • Exterior was professionally finished with new paint 2015 at American Custom Yachts
  • The paint is of the highest quality with no apparent sags, runs, orange peels or any other abnormalities
  • The superstructure is painted white with dark blue feature stripes
  • The main deck and cockpit are painted white
  • The hull is painted dark blue
  • The raised toe rail has been finished with a teak color as has the transom
  • The original factory aluminum bumper system was upgraded to a phenolic high impact white fender system provided by High Tide Marine in 2007
  • The cockpit sole and covering boards are covered with teak and look new
  • There is a transom door with hinged upper opening on the starboard side to allow boating of large fish
  • There is a Release Marine Teak 120# fighting chair equipped with a rocket launcher and mounted with an offset 4” polished SST pedestal installed new in 2014
  • Forward cockpit is configured with machinery space access door, water supplied bait rigging sink area, below tackle locker drawers, built in bait freezer and live well
  • The after cockpit area under the deck is fitted with a large capacity fish box with removable hinged hatches
  • The perimeter of the cockpit is equipped with new high quality marine grade white bolsters with blue beading in 2015

  • The salon was redesigned and refitted in 2007
  • Salon cabinetry was refinished and teak trim added in 2007
  • The port seating area was re-upholstered in 2007 and is in like new condition
  • There is a Murray Brothers custom inlay highly finished table with removable top to allow storage installed in 2007
  • The overhead was fitted with a high quality beige vinyl removable panel system in 2014
  • There is a custom built-in hidden 6 rod storage area in the overhead installed in 2007.
  • There is a custom access removable panel that allows entry to the underside of the fly bridge helm from the interior that allows maintenance in inclement weather installed in 2014
  • The salon sole was fitted with a deep pile beige carpet installed in 2014
  • The starboard forward area has a wraparound upholstered dinette seating area and bright work finished dinette table supported by two 4” SST pedestals
  • There is a Guy Harvey “Heaviest Blue Marlin trophy forward starboard bulkhead
  • The starboard cabinetry contains a flat screen Sharp LC 32 GC6 TV secured using custom built top mount bracketing
  • There is a Direct TV receiver system located in cabinet under the TV
  • There is new LED recessed lighting installed in 2014
The Galley configuration for this vessel was originally built below decks to starboard.  The original galley was completely removed and relocated and refitted at the forward end of the salon area.  The current configuration is a U-shaped open to the center line with forward overhead cabinetry and new below counter storage cabinets and appliances.  The galley is separated from the salon area by a built in custom bar style cabinet covered with a high quality blue solid surfacing material.  There is a bright work finished sea rail around the perimeter of the solid surfacing.  There are three SST pedestal mounted bar stools on the aft side for seating at the bar. The forward counter top is also covered with matching solid surface blue pattern material.
  • There is a recessed Kenyon 2 burner Eurokera cooktop
  • There is a Miele restaurant grade espresso machine stored in the port storage cabinet
  • There is a Sharp R55T8-F micro wave oven
  • There is a two drawer style GE Monogram SST refrigerator/freezer unit located below the bar top installed in 2007
  • There is a GE Monogram ice maker below the bar installed in 2007
  • There is a two drawer style GE Monogram SST refrigerator/freezer located under the forward counter top
  • The galley sole is covered with teak and holly installed in 2007
  • There is new LED recessed lighting installed in 2014
Tackle Room
  • There is a custom built one of a kind tackle room constructed in the location of the original galley down configuration removed in 2007 on the starboard side
  • The compartment is equipped with a custom glass locking door that is inscribed with the Bertram Yacht logo and “Melina”, Bertram Tackle Room
  • The overhead and the walls are covered with a phenolic type mirror surface that reflects all the equipment stored within
  • The locker is equipped with custom built teak rod and reel racks
  • There is new LED recessed lighting installed in 2014
Master Stateroom
  • The Master Stateroom is located on the port side forward below deck.  This space was completely refitted in 2014
  • The original queen berth and all cabinetry was removed
  • The space now contains two custom built and sized berths
  • One to inboard and one to outboard that are positioned longitudinally (forward and aft)
  • There are wraparound cabinets located above the new berths in a u shape configuration
  • The new cabinetry and bunks are a cherry veneer and finished in a semi-gloss finish
  • There are mirrors on the aft bulkhead and in and outboard bulkheads are covered with padded marine grade vinyl beige panels
  •  There is new carpet on the sole
  • The overhead has new padded marine grade vinyl beige panels
  • There is new LED recessed lighting installed in 2014
Master Stateroom Head
  • The Master Stateroom head was refitted in 2007 and remains the same with few exceptions
  • The head is in like new condition still
  • The sink vanity top is solid surfacing
  • The bulkheads were refitted in 2014 with new padded marine grade vinyl beige panels
VIP Stateroom
  • New LED recessed lights were installed in 2014
  • The VIP stateroom original configuration of a centerline queen bunk and cabinetry was refurbished in 2012.
  • The finish is a cherry veneer
  • There are two upper custom built and sized bunks with one port and one starboard of similar dimension’s and one full size custom built and sized bunk lower to starboard below the upper bunk
  • The wall coverings are of a high grade marine beige vinyl
  • The overhead is a high grade marine beige vinyl
VIP Head
  • The head is located aft to port side and is accessible from the VIP Stateroom
  • The wall coverings are of a high grade marine material in like new condition
  • The sole is covered with teak and holly
  • There is a custom built in shower stall with glass door
  • The sink vanity is a solid surface material
Crew/Guest Stateroom
  • This stateroom is located on the starboard side forward of the guest head and tackle room and is accessible from the centerline passageway
  • The wall coverings were renewed in 2008
  • There is recessed overhead LED lighting installed in 2014
Guest Head
  • The guest toilet space is located on the starboard side forward of the tackle room
  • This space is accessed from the centerline passageway or the Crew/Guest stateroom forward of this space.
  • This space was completely renovated in 2007
  • The bulkheads and overhead is covered with a high quality marine grade covering
  • The sink vanity is covered with a solid surface material
  • There is a built in shower stall with custom door
  • There is a marine grade toilet
  • The sole is covered in teak and holly
  • Oil Discharge located in the machinery space
  • Garbage Disposal located in the machinery space
Electronics - New 2016
  • Complete Outrigger Camera System 
  • KVH TV and Phone 
  • WiFi and Cell 
  • TV's throughout 
  • Complete Garmin Package 
Electrical Systems
Starboard Generator:

Make: Cummins EQD Onan Marine
Model: 17MDKBP-5183C
Serial Number: L070141620
Output: 17 Kva
Voltage: 120/240 AC
Hours: 744.50
Installed new in 2008

Port Generator:

Make: Cummins EQD Onan Marine
Model: 17MDKBP-5183C
Serial Number: L070141621
Output: 17 Kva
Voltage: 120/240 AC
Hours: 830.80     
Installed new in 2008
  • Alternating Current (VAC)
  • Shore Inlet 50 amp 240 VAC
  • Main Electrical Distribution Panel starboard aft salon
  • Voltage 120/240 VAC
  • Main Circuit Protection Double pole circuit breakers engine room and main panel
  • Branch Circuit Protection Double pole circuit breaker
  • Generator 1 main circuit protection Double pole circuit breaker
  • Generator 2 main circuit protection Double pole circuit breaker 
  • Meters AC amps, volts and main panel
  • Conductors Thermoplastic encapsulated mult-stand copper with three conductor boat cable rating at 600 V 105C dry 75C wet rating
  • Direct Current (VDC)
  • Voltage 24 VDC with 12 volt batteries installed in series for 24VDC use
  • Main Engine start per engine 2 deep cycle maintenance free batteries group 31 1200 amp MCA 1550  Amp
  • Generator start per unit 1 deep cycle maintenance free batteries group 31 1200 amp MCA 1550 Amp
  • 24 VAC marine converter Raritan Crown 2B
  • 24 VAC marine converter Sentry 24V 40 amp battery charger
  • Battery equalizer Vanner volt master 60-50A high frequency balanced battery equalizer (2)
  • Main circuit protection Main disconnect switches in the machinery space
  • Branch circuit protection Single Pole circuit breakers at main panel
  • Conductors Thermoplastic encapsulated battery cable and thermoplastic encap
  • 200k Garmin refit 2016, all electronics, Latham cams, VSAT, HDTV, cell phone and extended Wi-Fi network, Custom dash installation
  • Hydraulic Rupp Tournament (Big) Riggers with LED lighted rigger tips 2015
  • New release fighting and helm chairs 2016
  • New heads and all plumbing fixtures, holding tank, etc. 2017
  • New LED lighting throughout with dimmers and new headliner 2016
  • Transom and toe rail new faux finish 2016
  • Master VIP done 2015, new bunks and Veem spare prop storage, bamboo mattresses
  • Eskimo ice Machine installed 2015
  • Galley moved from below to main salon in 2005, existing galley converted to tackle room
  • Salon AC replaced 2016 with new units installed in conditioned areas of salon...not bridge and cowl, air distribution along top of salon windows...better air distribution and eliminated condensation issues
  • New bridge opening into salon ceiling 20" x 72" above Velcro head liner provides stand up access to all bridge electronics
  • Bilges all painted 2017
  • Repaint entire vessel 2016. Hull is AlexSeal Peppermint Blue Metallic, topside white, under hardtop lite ice blue, transom and toe Raik faux paint, white gold leaf lettering 

Other Features
  • The engines are MTU 16V 2000 with 1700 hrs. new in 2008
  • MTU engine warranty till Aug 2018
  • Generators are Onan 21 KW x 2 new in 2008
  • 2 Release helm chairs 2016
  • Release fighting chair with standoff 2016
  • 3 Latham cameras 2 on riggers one centerline
  • Rupp tournament “Big Rig” outriggers
  • Salon AC’s replaced and moved out of the flybridge and into salon 2014
  • New Veem props stowed under bunk in master
  • Eskimo ice machine
  • Frameless windows done at American Custom Yachts $50,000 2014
  • Underwater lights 2014
  • All lights switched to LED
This is truly a one of a kind 60 Bertram.  Repowered with 16V 2000’s, she is an animal, and fast.  Repowering was overseen by Lee Dana, Bertram Yachts longtime engineer. 

She is tricked out for tournament fishing and has a proven record.  If you have ever wanted one of Bertram’s greatest boats this is a special one.
Get More Info

Stay up-to-date on industry reports, upcoming events, and the newest listings on the market!